How to Put a Hose on a Hose Reel: The Basic Tips

How to Put a Hose on a Hose Reel: The Basic Tips

A durable and high-quality garden hose is not cheap, so it is best to take good care and to protect your investment. This is usually done by coiling the hose neatly to a hose reel to prevent kinking, abrasions, and possible cracking. As such, you must learn how to put a hose on a hose reel.

What Are the Benefits of Using Hose Reel?

Taking good care of the indispensable garden hose can be done with the use of a hose reel. Some of the amazing benefits of this small, powerful tool are as follows:

  • Conveniently increase the productivity in dispensing fluids
  • Efficiently store the hose as well as the fluid
  • Reduces wearing and tearing of the hose over time
  • Promotes safety by preventing hazards and serious accidents

How to Install or Replace a Garden Hose?

Before learning how to put your garden hose on a hose reel, let us first take a look at how to remove the old hose and install a new one. Here are the recommended steps:

  1. Disconnect the hose reel from the faucet spigot, and then evaluate and inspect the hose spigot for any possible vacuum breaker attachment. These vacuum breakers are required as a safety measure to prevent water contamination through back-siphoning into the fresh supply of water. If the breakers are all good, then you can proceed.
  2. Move the hose reel to an area where you can easily drain the water out of the hose. Keep in mind that as you remove the old hose, the water inside it will start to flow out.
  3. Once the hose is fully extended, the water coupling located in the inner drum will be visible inside the hose reel. Using your hand or adjustable pliers, disconnect the hose from the coupling.
  4. Unpack the new hose and then carefully straighten it out to eliminate bends. One time placing of the hose under the sun may help soften and make it more pliable to wind into the hose reel.
  5. Start assembling the hose reel if it needs to be replaced, too.
  6. Insert the rubber or vinyl washer of the hose coupling on the female end of the new garden hose. This will allow the watertight seal against the coupling of the drum.
  7. If there is a guide opening on the hose reel, insert the female end of the hose through this opening.
  8. Thread the female end of the hose to the water coupling present on the inner drum of the hose reel. Tighten firmly with the use of pliers. Be sure not to tighten too much to prevent breakage of the thread. The water coupling has plastic parts that can be damaged with too much force.

How to Put a Hose on a Hose Reel?

Now that the garden hose is properly installed, it’s time to begin putting the hose on a hose reel. This is done by simply following these basic instructions:

  1. Begin to wind the hose on the drum of the reel by taking time to feed the hose back and forth across the drum. This usually requires a clockwise rotation of the reel handle.
  2. Be sure to grip the hose with one hand as you turn the reel handle with the other hand.
  3. In cases where you are installing the garden hose on an electric hose reel, the retraction button should be pushed down to start winding the hose into the reel.
  4. Be sure to inspect the feeder hose that connects the hose reel to the faucet spigot. This should always be in good condition; no form of any cracks and kinks.
  5. If the feeder hose uses the female couplings, be sure to insert the coupling and check if the rubber or vinyl washers are in good condition.
  6. If the feeder hose is attached to the hose reel drum using a hose clamp, make sure that it is tightly clamped down around the drum’s nipple.

What Are the Alternatives?

When your hose reel accidentally stops functioning, alternative solutions and techniques can help save your indispensable garden hose. This involves manual preparation, winding, and storing of the garden hose.

1. Preparing the Hose

The hoses filled with water are hard to manipulate into a neat coil due to their heavier and messier condition. Be sure to remove any sprinkler and hand spray attachment before winding the hose.

Leave the hose fully extended or uncoil it to its full length. A slight incline near the end of the hose can help facilitate draining.

2. Coiling Techniques

Once the hose is drained, start coiling at the end where the faucet is attached. Begin to wind the hose into loops of 24 to 36 inches in diameter.

Leave the end at the beginning of the loop and on the ground to help drain any lingering water. Pull the other end of the hose up and drop it down in its natural curves.

Some recommend winding the hose around a trashcan in order to create a neat stack of a coiled hose. The trashcan is then lifted when the coil is complete and secured with a hook and loop tape at two opposite sides. The smaller hose can be coiled inside a large garden pot.

3. Hose Storage

Once the hoses are coiled, it is best to store them flat. They should also be kept off the ground to prevent mildew formation.

Hanging of the hose in a single hook can cause its sidewall to develop permanent dents. Thus, using two hooks or broad arched support is recommended if you plan to hang or store the hose on a wall.

Final Thoughts

The garden hose is an essential piece of outdoor equipment that offers numerous benefits such as watering the plants in your garden and lawn, rinsing off backyard stuff, and even washing your cars. The use of a hose reel protects the hose against damage and increases its efficiency.

Learning how to put a hose on a hose reel requires simple knowledge and helpful tools. This is done through simple preparation procedures and techniques either by operating a crank or by a spring-loaded type.

The conventional method can also be used in case the reel stops working. All these are done to ensure that your garden hose is in good working conditions at all times.

Spread the love
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •